Swages, Flatters, Fullers

Swages are commonly uniform in shape and are for forming round stock to size after forging.  In some cases top and bottom tools are hinged or fastened together by a spring strap or rod called a Spring Swage. These can be useful when a smith is working alone. Both are also used at power hammers and on fly presses.

Pieh Tool Hand Fullers

Pieh Legacy Collection!

This will be useful in many decorative blacksmithing projects. They are between 7-8 inches in length and made from  round S7 tool steel.

Get our whole collection of S7 tools by navigating to our punch sets. Made in USA. 

Peddinghaus Square Flatter

Flatters have flat faces with sharp or rounded edges and are positioned on the work piece and struck with a sledge hammer or other hammer. The set hammer is most often used for setting in shoulders, while the flatter is a good finishing tool and should be used specifically to leave a good finish on flat surfaces.

Handles is made from ash wood.

Picard Square Flatter

Flatters have flat faces with sharp or rounded edges and are positioned on the work piece and struck with a sledge hammer or other hammer. The set hammer is most often used for setting in shoulders, while the flatter is a good finishing tool and should be used specifically to leave a good finish on flat surfaces.

Handles is made from ash wood.

ex Shipping lbs

Peddinghaus Top Swage, 10 mm (3/8 in.)

Peddinghaus Swages are drop forged. Use with the Peddinghaus Bottom Swage. Swage features a long ash wood handle.
ex Shipping lbs

Peddinghaus Top Swage, 15 mm (5/8 in.)

Peddinghaus Swages are drop forged. Use with the Peddinghaus Bottom Swage. Swage features a long ash wood handle.
ex Shipping lbs

Peddinghaus Top Swage, 20 mm (3/4 in.)

Peddinghaus Swages are drop forged. Use with the Peddinghaus Bottom Swage. Swage features a long ash wood handle.
ex Shipping lbs

Iron Mountain Bottom Fuller Hardy

Fullers are forming tools of different shapes used in making grooves or hollows. They are often used in pairs, the bottom fuller has a square shank which fits into the hardy hole in the anvil while the top fuller has a handle. The work is placed on the bottom fuller and the top is placed on the work and struck with a hammer. The top fuller is also used for finishing round corners and for stretching or spreading metal. The tool has a .1/2 " radius and is 2 1/2" long. This tool is used by many different craftsman in lots of different trades to lengthen steel primarily in the blacksmith trade. The tool is made of tough 60/45/18 ductile iron. These castings have been produced for many years and have proven to be very reliable and useful. This tool is offered with a 3/4" - 1" and 1 1/4" hardy post. All our tools are new and in very good condition. Casting weighs approx. 3 lbs. Made in the USA!

Iron Mountain Bottom Swage Hardy

Artistic. Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow, a special Artists' block is then often used.  This tool is designed for flexibility. In addition, individual blocks may contain unique features of specific use or relevance to a particular smith or branch of the blacksmiths craft. This tool is approx. 4" high including the hardy post and 2 3/8" long and 1 1/2" across the forming surface. This tool is used by many different craftsmen in lots of different trades to form and swage materials. This tool can be used with a top set or ball pien hammers to bend draw and tenon materials. This tool can also be used for any other free forming you may come up with. The tool is made of tough 60/45/18 ductile iron.  These castings have been produced for many years and have proven to be very reliable and useful. This tool is offered with a 3/4" hardy post.  All tools are new and in very good condition. Casting weighs approx. 3 lbs. Made in the USA!

ex Shipping lbs

Iron Mountain Dog Bone Swage Hardy

The Dog Bone swage is 4 1/2"  long and 2" wide and approx. 3/4" deep. This is a very useful tool. The swage is made of tough 60/45/12 ductile iron.  The swage is available with a 3/4" 7/8” 1” and 1 1/4” hardy post to use in your anvil, vise or stake plate. The swage is used by Blacksmiths and Tinsmiths to form rose petals, ladle ends, candle cups, and to turn leaves etc. These swages have been produced for many years and have proven to be very reliable and useful.  All tools are new and in very good condition. Casting weighs approx.3 lbs. Made in the USA!

Iron Mountain Large Spoon Swage

High Quality Spoon Swage

Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow. We developed swage blocks that are individual and easy to handle and can be held in a vise. No more searching for the heavy expensive swage blocks or having to manhandle the one you might already own. This spoon swage is oval in shape and measures 2" wide and 2 3/4" long. Uses include making spoons, finger guards for armorers, making flower petals just to name a few.  The tool is cast steel is very durable. As with all the tools we produce this swage will last well into the next generations.

ex Shipping lbs

Iron Mountain Radius Block Hardy

SAVE THE EDGE OF YOUR ANVIL FACE! 

This tool is approx.4" high including the hardy post and 2" square  across the forming surface. This tool is used by many different craftsman in lots of different trades to form and swage materials. The block is used for necking a specific radius on your project to save the edges of the anvil. The block has 4 sides with increasing radius from sharp to 3/8". This tool can be used with a top set or ball pien hammers to bend draw and tenon materials and any other free forming you may come up with. The tool is made of tough 60/45/18 ductile iron.  These castings have been produced for many years and  have proven to be very reliable and useful. This tool is offered with a 1" hardy post.  All tools are new and in very good condition. Casting weighs approx.4 lbs. Made in the USA!

Iron Mountain Deep Ladle Swage Block Vise Tool

Quit Lugging Around Your Heavy Swage Block and Try This One! 

Are you making Armor, candle cups, kitchen ladles/skimmers, or flowers etc? This is the tool for the job. Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow. We developed swage blocks that are individual and easy to handle that can be held in a vise. No more searching for the heavy expensive swage blocks, or having to manhandle the one. This ladle swage is 3 1/2"  in diameter and approx. 1 1/2" deep. The wide rim was designed to fold the rim of the part being produced to invert the apart and make courting candle bases. Don't be confused by the size because it will form much larger pieces by just moving the project from side to side. You can form half rounds and make a ball. The swage is made of tough 60/45/15 ductile iron.  The swage has a 3/4'' wide bar on the back side so that can be used in a vise. The swage is used by Blacksmiths and Tinsmiths to form shallow bowls, ladles, candle cups, etc. Our swages have been produced for many years and  have proven to be very reliable and useful. Made in the USA!

Iron Mountain Shallow Ladle Swage Block Vise Tool

Quit Lugging Around Your Heavy Swage Block and Try This One! 

Are you making Armor, candle cups, kitchen ladles/skimmers, or flowers etc? This is the tool for the job. Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow. We developed swage blocks that are individual and easy to handle that can be held in a vise. No more searching for the heavy expensive swage blocks, or having to manhandle the one. Don't be confused by the size because it will form much larger pieces by just moving the project from side to side. Our swages have been produced for many years and  have proven to be very reliable and useful. Made in the USA! The ladle swage is 4"  diameter and  1/2" deep approx. The swage is made of tough 60/45/15 ductile iron. Casting weighs approx.5 lbs. Buyer pays shipping cost. Made in the USA!

ex Shipping lbs

Iron Mountain Rose Petal Swage, Large (for vise)

Make Something Nice for Someone Special in Your Life. 

Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow. We developed swage blocks that are individual and easy to handle that can be held in a vise. No more searching for the heavy expensive swage blocks or having to manhandle one. The rose swage is used to form rose petals, leaves and shallow bowls. The tool is approx.3 3/8" long and 2 3/4" wide and approx. 1" deep. This is a very useful tool. The swage is made of tough 60/45/15 ductile iron.  The swage has a 3/4'' x 2 1/2" bar to use in your vise. The swage is used by Blacksmiths and Tinsmiths to form the ends of consistent shapes of leaves and petals etc. These swages have been produced for many years and have proven to be very reliable and useful. Casting weighs approx.6 lbs. Made in the USA!

ex Shipping lbs

Iron Mountain Rose Petal Swage Hardy, Small

SMALL ROSE PETAL SWAGE 1" HARDY

The rose petal swage used to form rose petals, leaves and shallow bowls. The tool is approx.4 1/4" long and 2" wide and approx. 1/2" deep. This is a very useful tool. The swage is made of tough 60/45/15 ductile iron. The swage has a hardy post to use in your anvil or vise.  These swages have been produced for many years and have proven to be very reliable and useful. Casting weighs approx.3 lbs. Made in the USA!

Iron Mountain Rose Petal Swage Hardy, Large

Artist Blacksmiths sometimes  require a tool that will allow metal to be  formed in ways that an anvil or traditional industrial swage block will  not allow. We developed swage blocks that are individual and easy to  handle that can be held in a vise. No more searching for the heavy  expensive swage blocks, or having to manhandle one. The rose swage is used to form rose petals,  leaves and shallow bowls.. The tool is approx.3 3/8" long  and 2 3/4" wide and aprox. 1" deep. This is a very useful  tool. The swage is made of tough 60/45/15 ductile iron.  The swage is used by  Blacksmiths and Tinsmiths to form the ends of consistent shapes of leaves and petals etc.  These swages have been produced for many years and  have proven to be  very reliable and useful. Casting weighs approx.6  lbs. Made in the USA!
ex Shipping lbs

Iron Mountain Butt Plate, Swage Block 1

This swage block is 4" long and 2" wide and has a 1" wide by 7/8" deep forming radius'. This tool was originally designed for preforming a brass butt plate for muzzle loading rifles. The tool has been proven very useful for other projects also. The swage is made of tough 60/45/15 ductile iron. The swage has a 3/4'' bar on the underside to use on your post vise or modify to use on your anvil. The swage is used by Blacksmiths and Tinsmiths to form round stock for tenons or making curls on thinner stock, etc.. These swages have been produced for many years and have proven to be very reliable and useful. Casting weighs approx. 5 lbs. Made in the USA!

Iron Mountain Swage Block 2

SWAGE BLOCK 2 RADIUS 1 3/4" AND 2" BLACKSMITH ARMOR TINSMITH JEWELERS

 

Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow. We developed swage blocks that are individual and easy to handle that can be held in a vise. No more searching for the heavy expensive swage blocks, or having to manhandle one. This swage block is 6" long and 2" wide and has 2 two 5 forming surfaces. The swage 2 has a 13/4 and 2" wide swage. These are very useful tools. The swage is made of tough 60/45/12 ductile iron. The tool has a 3/4'' bar on the underside to use on your post vise or modify to use on your anvil. The swage is used by Blacksmiths and Tinsmiths to form round stock for tenons etc.

ex Shipping lbs

Iron Mountain Swage Block 3

This Tool Is the Answer to your Huge Swage Block. 

Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow. We developed swage blocks that are individual and easy to handle that can be held in a vise. No more searching for the heavy expensive swage blocks or having to manhandle one. This swage block is 6” long and 2" wide and has 3 forming radius'. The width of each radius is 1"- 1 1/4"-and1 1/2". This is a very useful tool. The swage is made of tough 60/45/15 ductile iron.  The tool has a 3/4'' bar on the underside to use on your post vise or modify to use on your anvil. The swage is used by Blacksmiths and Tinsmiths to form round stock for tenons etc. These swages have been produced for many years and have proven to be very reliable and useful. Casting weighs approx.7 lbs. Made in the USA!

Iron Mountain Swage Block 4

Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow. We developed swage blocks that are individual and easy to handle that can be held in a vise. No more searching for the heavy expensive swage blocks or having to manhandle one. This swage block is 6” long and 2" wide and has 4 forming surfaces'. The width of each form is 2 V- dies one is 1/2" wide by 3/8" deep and the other is 1 1/4" wide by 3/4" deep. The other two forms are tapers for making sockets and or other forms. The sockets measure 3/4" tapers to1" on the smaller of the two and the larger measures 3/4" by1 1/2".  This is a very useful tool. The swage is made of tough 60/45/15 ductile iron.  The tool has a 3/4'' bar on the underside to use on your post vise or modify to use on your anvil. The swage is used by Blacksmiths and Tinsmiths to form round stock for tenons etc. These swages have been produced for many years and have proven to be very reliable and useful. Casting weighs approx.7 lbs. Made in the USA!

ex Shipping lbs

Iron Mountain Swage Block 5

Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow. We developed swage blocks that are individual and easy to handle that can be held in a vise. No more searching for the heavy expensive swage blocks or having the manhandle one. This swage block is 6” long and 2” wide and has 5 forming radius’. The width of each radius is 3/8” – ½’ – 5/8” – ¾” and 7/8”. This is a very useful tool. The swage is made of tough 60/45/15 ductile iron. The tool has a ¾” bar on the underside to use on your post vise or modify to use on your anvil. The swage is used by blacksmiths and tinsmiths to form round stock for tenons etc. These swages have been produced for many years and have proven to be very reliable and useful. Casting weighs approx. 7 lbs. MADE IN USA!

Iron Mountain Small Spoon Swage

High Quality Teaspoon Swage

Artist Blacksmiths sometimes require a tool that will allow metal to be formed in ways that an anvil or traditional industrial swage block will not allow. We developed swage blocks that are individual and easy to handle and can be held in a vise. No more searching for the heavy expensive swage blocks or having to manhandle the one you might already own. This spoon swage is oval in shape and measures 1 1/4" wide and 2" long. Uses include making spoons, finger guards for armorers, making flower petals just to name a few.  The tool is cast steel is very durable. As with all the tools we produce this swage will last well into the next generations.

Iron Mountain Scroll Starter

The swage has a 1'' hardy post to use in your anvil, vise or stake plate. The swage is used by Blacksmiths and Tinsmiths to form the ends of consistent scrolls etc. These swages have been produced for many years and  have proven to be very reliable and useful.